Structural Fire Damage Cleaning in Olean, NY
The drywall is gone, and now you are staring at blackened studs, scorched joists and a charred roof deck. Somebody now has to decide what gets blasted clean, what gets sistered and what gets replaced. Unify Fire Solutions connects you with independent, licensed and insured contractors in Olean who clean the framing, masonry and steel itself.
- Soda, dry ice and hand cleaning of framing
- Every stud and joist probed for char depth
- Cleaned wood encapsulated against lingering odor
What Makes Framing Work Different
Close up the walls over dirty framing and the smoke odor bleeds right back through the new finish. Cleaning the structure is the step that decides whether the rebuild smells like a new house or a campfire.
Licensed & Insured Independent Pros
Each contractor on our referral list is an independent, licensed and insured local company. Verify both, and ask whether the crew follows the IICRC S700 standard for fire and smoke work.
Upfront Written Estimates
Blasting is priced by surface area, media and access, and attics and crawlspaces cost more to reach. Ask for a line-item written estimate before the first bag of media is opened.
Rapid Local Dispatch
Day or night, a dispatcher picks up and starts looking for a structural cleaning crew right away. Timing depends on which crews near Olean are free, and it is often the same day.
Blasting Rigs and Probing Tools
Structural crews bring soda blast pots, dry ice units, big compressors, HEPA vacs, air scrubbers and a sharp awl to test every member.
Stay out of a fire-damaged attic, and never walk a charred roof deck to check it. Weakened joists and burned-through sheathing can give way without warning, and exposed wiring may still be live. Wait for the contractor to check that the structure is safe, and keep people off floors that sit over a burned crawlspace or basement.
Structural Cleaning Services From Rafters to Slab
This is not contents cleaning and it is not debris haul-out. This page is about the framing, masonry and steel that actually carry the load.
Char Depth Probing and Member Decisions
Pressing an awl into the blackened wood shows how deep the char goes; a shallow crust over firm wood usually means it can be cleaned. When the char cuts deep into a joist or a truss web, the member gets sistered or swapped out.
- Members marked clean, sister or replace
- Structural engineer called in for questionable beams, trusses and headers
- Photos of each marked member for the claim
Soda Blasting
Sodium bicarbonate is softer than wood, so it strips soot and light char off studs, joists and roof decking without gouging the grain. Expect fine dust and residue that has to be contained and HEPA vacuumed when the blasting is done.
Dry Ice Blasting
With dry ice the pellets sublimate on impact, so there is nothing left on the floor but the soot itself. It works well in tight attics and around wiring, though it costs more and is noisy.
- Hearing protection and ventilation required
- Good choice when residue would be a problem
Wire Brushing and Sanding
Small, isolated char spots are often handled by hand with wire brushes and sanders tied into a HEPA vacuum. It is slow on big areas but precise where blasting would be overkill.
Brick, Block, Concrete and Steel Beams
Fireplace surrounds, block foundation walls and concrete slabs hold soot in their pores, and alkaline cleaners, scrubbing or blasting pull it out. Steel beams get cleaned and inspected for any heat warping, with doubts sent to the engineer.
Encapsulation and Attic Insulation Removal
Cleaned framing gets a coat of shellac-based or specialty encapsulant to lock in any odor left deep in the wood. In the attic, smoke-soaked blown-in or batt insulation is vacuumed out with a high-powered insulation vac before the rafters and decking are cleaned.
Under the house, the crew probes the joists, sill plates and subfloor underside, then blasts and seals what can stay. Expect a vapor barrier to be pulled and replaced if smoke or hose water soaked it.
Ask your contractor which method they recommend for each area and why. A good crew may soda blast the open walls, dry ice the attic around the wiring and hand sand a few studs near the panel.
Plan for containment, because blasting throws soot and media into every corner it can reach. The crew hangs poly over doorways, masks off the HVAC returns and runs air scrubbers under negative pressure while they work. Ask what the plan is to shield the undamaged rooms, floors and glass.
Bare Framing Covered in Soot and Char?
Ring the dispatch line and we start finding a structural cleaning crew near Olean. It costs nothing to call.
Call +1-833-336-1630How a Structural Cleaning Job Unfolds
- 1
Phone the Dispatcher
Say which parts of the structure are open now, such as walls, attic, crawlspace, masonry or steel. Mention if a roofer, engineer or adjuster has already been out.
- 2
Mobile Crew on Site
The contractor arrives with a compressor, blasting equipment and containment materials. They check that the roof and floor are safe to walk and that power to the open walls is off.
- 3
Probe, Mark and Quote
They test each stud, joist and rafter with an awl, tag it, and flag anything doubtful for an engineer. A written, itemized quote covering area, blast method, encapsulant and attic insulation comes before any work starts.
- 4
Blasting, Sealing and Walkthrough
After blasting and HEPA cleanup, the framing gets its sealer coat, and you walk the bare structure with the crew lead. Do a sniff test on a warm afternoon, and ask for photos of every marked member before the rebuild closes the walls.
Notes From People We Connected
After the attic fire, the rafters were black and the blown-in insulation was a wet mess. The crew pulled the insulation, dry ice blasted the rafters and rolled sealer on everything. An engineer looked at two deeply charred rafters and they were sistered instead of torn out.
I assumed every black stud in the hallway had to be replaced. The crew lead probed each one with an awl and showed me that most were just surface char. They soda blasted and sealed them, and only three were swapped.
The fire in our lower level left the block walls and the steel beam coated in soot. The contractor cleaned the block and the beam, then had an engineer check the steel for warping. No smell now, even with the windows shut.
Common Questions About Cleaning Charred Framing
How do crews decide if a charred stud can stay?
They probe it. An awl or screwdriver pushed into the black surface shows how deep the char goes, and wood that is firm just under a thin crust can usually be blasted and sealed. Deep char, cracks or a reduced cross section mean sistering or replacement, with a structural engineer making the call on anything questionable.
What is the difference between soda blasting and dry ice blasting?
Soda media is mild on the grain and helps with odor, though it leaves a white dust that needs a full HEPA cleanup. Dry ice pellets vanish on impact, so cleanup is easier and it works well around wiring, but it is louder and usually costs more. Many crews use both on the same house.
Why seal the framing if it has already been cleaned?
Wood is porous, and smoke molecules sit deep in the grain where no blasting can reach. A shellac-based or specialty encapsulant locks that residual odor in so it cannot off-gas through the new drywall. Sealing dirty wood does not work, so the cleaning has to come first.
Does the attic insulation have to come out after a fire?
If smoke reached the attic, almost always yes. Loose-fill and batts act like a giant filter for smoke, and hose water often soaks them as well. Crews vacuum it out with a truck-mounted or portable insulation vac so the rafters and decking can be inspected and cleaned before new insulation goes in.
Can soot be cleaned off brick and concrete block?
Usually yes, though masonry takes more effort than drywall because soot sinks into the pores. Expect alkaline detergents and scrub brushes for light staining and media blasting for thick deposits. Heat-cracked or spalled block and brick should be looked at by an engineer or mason.
Do I need a structural engineer for fire-damaged framing?
Not for every job, but for anything load-bearing that looks questionable, yes. Trusses, beams, headers, steel and heavily charred joists are where an engineer's letter protects you and helps the claim. Your local building department may also require one before the walls close.
Charred Framing Cleaning Across Olean and Beyond
Our dispatch line covers Olean and the nearby communities around it, from older homes with plaster and solid-sawn joists to newer builds with engineered trusses. Attics, basements, crawlspaces, garages and light commercial spaces all come up regularly.
- Attic fires
- Electrical fires
- Furnace puff-backs
- Chimney fires
- Lightning strikes
- Neighbor's fire spread
Should the first contractor not suit you, ring us again and we will connect you with a different one. Do not let the rebuild close walls over dirty framing.
